MN160 digital decoder 0.5A 7 stranded wires. Dimensions: 13 x 7.5 x 1.6mm; equipped on one side. Wired variant of the MN160: 7 free wires (2x motor, 2x rail, front light (FA0v), rear light (FA0r), common positive pole).Zimo non-sound decoders are technologically equivalent to the MS sound decoders. The identical microcontrollers and largely the same components for the power electronics (motor output stages, etc.) are installed in both product classes, and of course the software is also largely (

Two Dumbos, high volume and good bass reproduction, the two Dumbo S in series, therefore suitable for Zimo large-scale-sound Decoders (which operate the speakers with 10V instead of 5V) when a largeer Visaton speaker no place. 50 x 15 x 14 mm, 16 Ohm / 2 W.

Two Dumbos in a box, higher volume (only suitable for 3 watt sound Decoders), but relatively little resonance volume, therefore a little weaker bass reproduction, 40 x 22 x 9 mm, 4 ohm / 2 W.

Connection board at the I2C bus for 16 signal lights, with screw terminals.

Digitally switchable clutch H0E for double tractions. Matching counterpart: Further H0e-D2 on the second vehicle of the double traction. All H0E couplings are suitable for H0E cars with a stern shaft.Technical data: Voltage: 12-22V DC, maximum current: 90mA, maximum load duration: 10 seconds, bobbin: brass, mechanics: permanent magnet, clutch recording: H0E, buffer distance: Corresponds to the buffer spacing of common clutches, operating temperature: -20 to 80 ° C . The clutch may be max. 10 sec

Digitally switchable coupling H0E for single tractions. All H0E couplings are suitable for H0E cars with a stern shaft.Technical data: Voltage: 12-22V DC, maximum current: 90mA, maximum load duration: 10 seconds, bobbin: brass, mechanics: permanent magnet, clutch recording: H0E, buffer distance: Corresponds to the buffer spacing of common clutches, operating temperature: -20 to 80 ° C . The clutch may be max. 10 seconds are loaded.The Digital clutches allow the uncoupling of cars to free route.

CAN bus cable 8pol 3 m length.

CAN bus cable 8pol 1 m length.

Finished CAN bus cable with plugs attached on both sides (also called driving cord) in 15 cm in length. The very short version is specifically suitable for connecting two side-by-side drivers.The Zimo Bus System, based on the industrial-proven CAN protocol, is the most powerful and reliable and reliable under the Digital system bus systems with at least 1000 messages / sec. The ZIMO system components, such as base units, booster, driveline, magneticle and track section modules, etc., are connect

MN180N18 Digital Decoder 0.7A Next18. 4 + 2 FA 4 amplified outputs + 2 SUSI + 2 logic level outputs according to the VHDM standard Direct connection of 15 V energy storage to solder pads (up to 15,000 µF).Technologically, Zimo non-sound decoders correspond to the MS sound decoders. The identical microcontrollers and largely the same components for the power electronics (motor output stages, etc.) are installed in both product classes, and of course the software is also (further) developed jointl

Amplifier module for a logic level output of a Decoder. Most ZIMO Decoders have such logic level outputs in addition to the normal function outputs, which are switched between 0 V (for OFF and 5V (for a) and need not be charged, but need an external amplifier. Mostly logic level outputs are an alternative use of the SUSI connections (Clock and Data), and are activated by CV # 124, bit 7 = 1. The output of the M4000Z supplies up to 0.5 A.

GER: PIKO SmartDecoder XP S TT BR 62 Next18 inkl. Lautsprecher

Basic device MX10EC + Roco WLAN mouse + USB stick + CAN cable + 8Pola1m + power supply NG300 + router + 3x battery + operating instructions. MX10

SwitchPilot Extension Adapter for ABC braking distances. Set of 2 pieces for a total of 4 brake sections. These adapter boards are simply plugged into the terminals of a SwitchPilot Extension module and greatly simplify the construction and wiring of ABC braking distances. Each adapter board can generate the signals for two braking sections. The ABC brake technology not only allows a gentle deceleration before signals, but also the triggering of functions during the signal stop. The sound functi

Adapter board Next-18 to NEM 658 16-pin PluX16.

Vehicle decoder with 6-pin interface.

Operating modes: Direct bus connection to ECoSlink. Operation with ECoS or Central Station Reloaded V3.0.0. possible. Feedback: 16 feedback sensors, configurable via jumpers as digital inputs (e.g., for track tracks or reed contacts) or as track occupancy detectors (current sensors). Galvanic isolation of the sensors from the control panel, maximum 3A current load per feedback input. RailCom®: 4 of the 16 sensors can be configured on request as a RailCom detector ("local detector"). Detection of

GER: PSD XP Sound E669.1 CSD PluX22 + Lautsprecher

Function Decoder, 20.5 x 15 x 3.5 mm, 1.2 A, 8 function outputs, energy storage terminal, with 21MTC interface NEM660.

GER: PSD S G 1700 PluX22

Decoder MX617N NEM651 6-pin pin strip, 13 x 9 x 2.5 mm, 24 V Voltage resistance, 0.7 A, 6 function outputs, no SUSI pins.General properties of ZIMO Decoders: DCC addresses 1 ... 10239, composite addresses 1 ... 9999 (SB 2017, Veren: 127), mm addresses 1 ... 80, functions F0 ... F12 ( .. F20 for sound), 14, 28 or 128 (external) driving steps, 256 or 1024 internal stages, programming the CVS in Service Mode (at the programming track) and in operational mode (with RailCom to acknowledge and read),

The Mobile Control Pro is ESU's latest answer to the question of how to combine the advantages of smartphone technology with the needs of model railway control. The Mobile Control Pro is essentially a compact Android-based tablet equipped with controls for controlling your locomotives and magnetic accessories. The connection to the digital command station is established exclusively wirelessly via Wi-Fi. A specially designed app by ESU can communicate directly with a variety of digital command st

The LokPilot 5 micro is the smallest digital decoder from ESU to date. Thanks to the use of subminiature components, 8-layer printed circuit boards and the latest manufacturing technology, it is so small with only 8.0mm x 7.0mm and a thickness of only 2.4mm (on the capacitor: 2.9mm) that it can be used even in very small locomotives Nominal sizes Z, N or TT can accommodate. Nevertheless, functionality and robustness were not spared compared to the larger versions. LokPilot 5 micro decoders are o

The LokPilot 5 micro is the smallest digital decoder from ESU to date. Thanks to the use of subminiature components, 8-layer printed circuit boards and the latest manufacturing technology, it is so small with only 8.0mm x 7.0mm and a thickness of only 2.4mm (on the capacitor: 2.9mm) that it can be used even in very small locomotives Nominal sizes Z, N or TT can accommodate. Nevertheless, functionality and robustness were not spared compared to the larger versions. LokPilot 5 micro decoders are o