Operation under DCC with RailComPlus®, M4, Motorola® and Selectrix®, 32 functions switchable (depending on the control panel), 32-bit processor, Digital Class "D" amplifier with up to 3 W power (LokSound 5 XL: 13 W), each channel in 16-bit resolution and 31250 kHz sample rate, noise memory with 128 Mbit capacity, motor control with 50 kHz clock speed, RC servos and Susi modules controllable, 3 new, individually adjustable brake controller, two-stage heavy load simulation, Updatable with ESU-LokP

Basic device MX10 + Roco WLAN mouse + USB stick + CAN cable + 8pola1m + power supply NG300 + router + 3x battery + operating instructions MX10

Miniature Rectangle Speaker with integrated resonant body, 11 x 15 x 9 mm, 8 ohm / 1 W.

Decoder MX637P22 with 22-pin PLUX22 interface NEM658, 22 x 15 x 3.5 mm, 1,2 A, 10 function outputs, no energy memory connection. Decoder MX637P22 with 22-pin PLUX22 interface NEM658, 22 x 15 x 3.5 mm, 1,2 A, 10 function outputs, no energy memory connection.General properties of ZIMO Decoders: DCC addresses 1 ... 10239, composite addresses 1 ... 9999 (SB 2017, Veren: 127), mm addresses 1 ... 80, functions F0 ... F12 ( .. F20 for sound), 14, 28 or 128 (external) driving steps, 256 or 1024 internal

Light board LIPLDHW1 neutral white LED interior lighting with decoder and second address as an aid to train formation. This is typically set to the address of the locomotive in the light boards and function decoders of a train. This creates the possibility of switching the interior lighting of all these cars, as well as the exterior lights of the rear or control car, using the function keys of a single address (usually the locomotive address). In order to be able to use this comfortably, light c

Decoder MX635P22 with 22-pin PLUX22 interface NEM658, 26 x 15 x 3.5 mm, 1.8 A, 10 function outputs, power store connection 16V (arbitrary capacity, also gold cap), semi-synchronous rectifier for higher motor current and total load capacity (until 1.8 A).General properties of ZIMO Decoders: DCC addresses 1 ... 10239, composite addresses 1 ... 9999 (SB 2017, Veren: 127), mm addresses 1 ... 80, functions F0 ... F12 ( .. F20 for sound), 14, 28 or 128 (external) driving steps, 256 or 1024 internal st

Decoder MX616R with 8-pin interface NEM652 on wires, 8 x 8 x 2.2 mm, 24 V Voltage resistance, 0.7 A, 6 function outputs, no SUSI pins.General properties of ZIMO Decoders: DCC addresses 1 ... 10239, composite addresses 1 ... 9999 (SB 2017, Veren: 127), mm addresses 1 ... 80, functions F0 ... F12 ( .. F20 for sound), 14, 28 or 128 (external) driving steps, 256 or 1024 internal stages, programming the CVS in Service Mode (at the programming track) and in operational mode (with RailCom to acknowledg

Decoder MX638C with 21MTC interface NEM660, 26 x 15 x 3.5 mm, 1,2 A, 6 function outputs, FA3, FA4 as logic level outputs (changeable via CV # 8), no energy memory connection.General properties of ZIMO Decoders: DCC addresses 1 ... 10239, composite addresses 1 ... 9999 (SB 2017, Veren: 127), mm addresses 1 ... 80, functions F0 ... F12 ( .. F20 for sound), 14, 28 or 128 (external) driving steps, 256 or 1024 internal stages, programming the CVS in Service Mode (at the programming track) and in oper

MN300F digital decoder 1.0A 6-pin interface NEM651 on wires. Variant of the MN300, 6-pin interface NEM651 on wires, 5 free wires.Technologically, Zimo non-sound decoders correspond to the MS sound decoders. The identical microcontrollers and largely the same components for the power electronics (motor output stages, etc.) are installed in both product classes, and of course the software is also (further) developed jointly to a large extent. These similarities cause, among other things, the same

PIKO SmartDecoder XP S Rh1067 PluX22 inkl. Lautsprecher

The LokPilot 5 micro DCC is the "twin" of the LokPilot 5 micro. With just 8.0mm x 7.0mm and a thickness of only 2.4mm (on the capacitor: 2.9mm), just as small that it can also be accommodated in very small locomotives of nominal sizes Z, N or TT, it is a pure DCC Decoder. This lack of flexibility is rewarded with a lower price. LokPilot 5 micro DCC decoders are available with all common interfaces. The variants with Next18 or PluX16 interface are a bit larger with a base area of ??13.0mm x 9.2mm

Sound Decoder NEM 651 6-pin interface on wires, 19 x 11 x 3.1 mm, with 6 foot outputs, 13 connecting wires (2 x rail, 2 x motor, 2 x acc. Plus, mass, 4 FU outputs, 2 x speakers), 2 solder pads (other FU outputs).

Decoder MX635P16 with 16-pin PLUX16 interface NEM658, 26 x 15 x 3.5 mm, 1.8 A, 10 function outputs, power store connection 16V (arbitrary capacity, also gold cap), semi-synchronous rectifier for higher motor current and total load capacity (until 1.8 A).General properties of ZIMO Decoders: DCC addresses 1 ... 10239, composite addresses 1 ... 9999 (SB 2017, Veren: 127), mm addresses 1 ... 80, functions F0 ... F12 ( .. F20 for sound), 14, 28 or 128 (external) driving steps, 256 or 1024 internal st

Function Decoder, 10.5 x 8 x 2.2 mm, 0.7 A, 6 function outputs, 9 stranded wires.

Miniature sound decoder, 12 connection wires (2 x rail, 2 x motor, common plus, ground, 4 FA, 2 x speakers), 19 x 7.8 x 2.8 mm, audio 1 W, 0.7 A.

MN330P22 digital decoder 1.2A PluX-22. Direct connection of 15 V energy storage to PluX pin strip (unlimited capacity), no wires.Technologically, Zimo non-sound decoders correspond to the MS sound decoders. The identical microcontrollers and largely the same components for the power electronics (motor output stages, etc.) are installed in both product classes, and of course the software is also (further) developed jointly to a large extent. These similarities cause, among other things, the same

MN300P16 digital decoder 1.0A PluX-16. 6 FA Direct connection of 15 V energy storage device to PluX pin strip (up to 15,000 µF).Technologically, Zimo non-sound decoders correspond to the MS sound decoders. The identical microcontrollers and largely the same components for the power electronics (motor output stages, etc.) are installed in both product classes, and of course the software is also (further) developed jointly to a large extent. These similarities cause, among other things, the same d

Permanent magnet like 235690 and 245480, for armature 231440, D = 19,1mm, for motor plate 231350 (drum collector motor). For the conversion of old Märklin® all-electric motors you need a permanent magnet. It replaces the previous field winding and helps your old locomotives in conjunction with a LokSound or LokPilot decoder to a driving behavior that you would never have expected the locomotives! In total, there are four different magnets, which is needed exactly depends on the anchor type. The

The LokPilot 5 DCC is the "twin brother" of the LokPilot 5. The two share almost all of the features, but the LokPilot 5 DCC is a pure DCC decoder and cannot be used on analog AC systems. This lack of flexibility is rewarded with a lower price. LokPilot 5 decoders are offered with all common interfaces. Operating modes: The LokPilot 5 DCC is a "pure-bred" DCC decoder. 14 to 128 speed steps are as natural as 2- and 4-digit addresses. Up to 32 functions can be triggered. Thanks to RailComPlus®,

Highly flexible cable, diameter 0.5mm, AWG36, 10m winding, color orange.

The LokPilot 5 DCC is the "twin brother" of the LokPilot 5. The two share almost all of the features, but the LokPilot 5 DCC is a pure DCC decoder and cannot be used on analog AC systems. This lack of flexibility is rewarded with a lower price. LokPilot 5 decoders are offered with all common interfaces. Operating modes: The LokPilot 5 DCC is a "pure-bred" DCC decoder. 14 to 128 speed steps are as natural as 2- and 4-digit addresses. Up to 32 functions can be triggered. Thanks to RailComPlus®,

LokPilot 5 Fx DCC Funktionsdecoder PluX22 NEM658The LokPilot 5 Fx DCC is a function decoder without a motor output and therefore perfect for installation in control cars or function models. As the "twin brother" of the LokPilot 5 Fx, it shares its properties and also the basic properties of all other LokPilot 5 decoders, but is a pure DCC decoder. The LokPilot 5 Fx DCC is supplied in three versions: In addition to the "classic" version with an 8-pin NEM 652 cable harness, a version for the 21MTC

LokPilot 5 Fx function decoder DCC/MM/SX 8-pin NEM652The LokPilot 5 Fx is a function decoder without a motor output and is therefore perfect for installation in control cars or function models. Because it speaks DCC with RailCom® as well as Motorola® and Selectrix, it can be used with all common digital centers. It shares its flexible function key assignment and the various light effects with the other LokPilot 5 decoders from ESU.The LokPilot 5 Fx is supplied in three versions: In addition to t

The LokPilot 5 Fx micro and its “twin” LokPilot 5 Fx micro DCC is an extremely small function decoder with a footprint of only 8.0mm x 7.0mm and a thickness of only 2.4mm (on the capacitor: 2.9mm). It is used in all vehicles of nominal sizes N to H0 that do not have an engine output, but should still be able to switch light effects. LokPilot 5 Fx micro decoders are always offered with an 8-pin interface. Operating modes: The LokPilot 5 Fx micro is a real multi-protocol decoder. It masters the