The Piko SmartDecoder 4.1 Sound is a universally usable digital decoder of the latest generation with 8 channels and 12 bit sound, various light outputs and a 1.2 A motor control. The Piko SmartDecoder 4.1 Sound masters the data formats DCC with Rail-ComPlus®, Motorola® and Selectrix®, is mfx-capable and can also be used on analog systems. The Piko SmartDecoder 4.1 automatically recognizes the respective operating mode. Up to 44 switchable additional functions can be called up. Sounds typical fo

Simple point motor decoder for Standard solenoid point motors, 2 wire main track or bus connection minimize wiring. The super easy learning decoder requires no special programing when addressing. This decoder features an easy to use screw terminal block to insert the wires into. There is also a 3 pin harnes to attach to the Surface Mounted Point Motor but with simple modification it can be fitted to other Solenoid Point Motors.

The new ESU PowerPack Maxi has been developed as a powerful addition to the LokSound L V4.0 / LokSound 5 L, but can also - if space is available - on all LokPilot V4.0, LokSound V4.0, LokSound V4.0 M4 and LokSound 5 and reliably supplies your locomotive with energy when driving over dirt and long routes. Two energy storage devices (5 Farad capacity each) buffer both the sound and lights and engine functions, allowing your models to continue without power for up to 3 seconds, depending on power c

Power supply unit 600W (30V, 20A) Meanwell HLG-600H-30A; 26x14,5x5cm; 3.4kg;

Function Decoder, 10.5 x 8 x 2.2 mm, 0.7 A, 6 function outputs, with 8-pin interface NEM652 on wires.

Decoder MX635R with 8-pin interface NEM652 on wires, 26 x 15 x 3.5 mm, 1.8 A, 10 function outputs, connection for energy storage 16V (arbitrary capacity, also goldcap), semi-synchronous rectifier for higher motor current and total load capacity ( up to 1.8 A).General properties of ZIMO Decoders: DCC addresses 1 ... 10239, composite addresses 1 ... 9999 (SB 2017, Veren: 127), mm addresses 1 ... 80, functions F0 ... F12 ( .. F20 for sound), 14, 28 or 128 (external) driving steps, 256 or 1024 inter

Sound Decoder, 6-pin interface NEM 651, 14 x 10 x 2.6 mm, audio 1 W, 0.7 A.

Sound Decoder, 14 x 10 x 2.6 mm, audio 1 W, 0.7 A, with 4 fu outputs, 12 connecting wires.

Two dumbos, high volume and good bass reproduction. 50 x 15 x 14 mm, 4 ohm / 2 W.

Dumbo with integrated resonance body, 18 x 13 x 13 mm, 8 ohm / 1 W.

Prefabricated module made of 7 in series connected gold caps in long form for Category 2 Decoders (for MS Decoders such as MS450 or MS440 as a greater alternative to Mgolang; for MX or MS large-scale Decoder - all types - as additional energy storage).Not allowed for MX Decoders (except major tracks) because charging transistor is not sufficiently powerful.Content: 1 x Golmlang Gold Cap Module 140,000 ?F / 16 V, 56 x 8 x 14 mm.

Digitally switchable coupling for double tractions. Matching counterpart: Further MK2 on the second vehicle of the double traction.Technical data: voltage: 12-22V DC, maximum current: 90mA, maximum load duration: 10 seconds, bobbin: brass, mechanics: permanent magnet, clutch recording: NEM 362 / NEM 363, buffer distance: approx. 1.5mm shorter than Roco universal coupling, operating temperature : -20 to 80 ° C. The clutch may be max. 10 seconds are loaded.The Digital clutches allow the uncoupling

This design of the adapter board contains voltage regulators for a functional stress of 1.5 V.Adapter board for 21MTC Decoder; The Decoder is plugged into the pin header of the adapter. About large solder pads the wiring within the locomotive CAN be made comfortable. The AdamtC adapter board is equipped with a rectifier that relieves the rectifier of the Decoder, creating this less loss heat and CAN deliver more power for it. Size: 44 x 26.5 x 6 mm.The adapter board Adamtc CAN be used along with

XP 5.1 Function decoder for Next18 interface

This design of the adapter board contains voltage regulators for a functional stress of 5 V.Adapter board for 21MTC Decoder; The Decoder is plugged into the pin header of the adapter. About large solder pads the wiring within the locomotive CAN be made comfortable. The AdamtC adapter board is equipped with a rectifier that relieves the rectifier of the Decoder, creating this less loss heat and CAN deliver more power for it. Size: 44 x 26.5 x 6 mm.The adapter board Adamtc CAN be used along with a

Adapter board for 21MTC Decoder; The Decoder is plugged into the pin header of the adapter. About large solder pads the wiring within the locomotive CAN be made comfortable. The AdamtC adapter board is equipped with a rectifier that relieves the rectifier of the Decoder, creating this less loss heat and CAN deliver more power for it. Size: 44 x 26.5 x 6 mmThe adapter board Adamtc CAN be used along with all 21MTC Decoders, which are a C-type - therefore, MX631C, MX634C, MX638C, MX636C, MX644C, ..

XP 5.1 Function decoder

An important part of the LokSound system is the loudspeaker. Therefore, only specially designed loudspeakers tuned to the sound decoder are used. Here is the old truism: the bigger the speaker, the better the sound. For this reason, speakers are offered in a variety of sizes. An essential accessory is the sound capsule, which gives the loudspeaker diaphragm the necessary sound pressure and is supplied with most loudspeakers. If you are not sure which speaker fits in your model, then we generally

Highly flexible cable, diameter 0.5mm, AWG36, 10m winding, color violet.

Power distributor MoBa distributor V1.2 ready-made module. Thanks to the MoBa distributor V1.2, it is possible to wire conveniently under the model railway system. New consumers or track sections can be quickly supplied with power using the high-quality screw terminals. All terminal points marked with "A" are connected through, just like all points with "B". There is a "B" terminal next to each "A" terminal. This means you can connect your consumers clearly without cable chaos. The status LEDs a

1 amp miniature switching relay, 16 volts. With the small switching relay loads can be switched, which require more power than a function output of the decoder can afford. In this case, simply switch the relay in between. If you want to use a smoke generator, you also need the relay, so that it can work properly.

As your facility grows and you need to connect additional ECoSBoost boosters and ECoSDetector feedbacks to your ECoS or Central Station, you need an ECoSlink terminal. ECoSLink terminal bus distributor plate, 6x Connect sockets, 1x 0.9m cable.

XP 5.1 Function decoder

Finished CAN bus cable with plugs attached on both sides (also called driving cables) in 5 m in length.The Zimo Bus System, based on the industrial-proven CAN protocol, with at least 1000 messages / sec is the most powerful and reliable under Digital system bus systems. The ZIMO system components, such as base units, booster, driveline, magneticle and track section modules, etc., are connected to each other via the CAN bus (Controller Area Network), and wrap it over its traffic with 125 kbit / s