Sound Decoder NEM 652 8-pin interface on wires, 19 x 11 x 3.1 mm, with 6 foot outputs, 13 connecting wires (2 x rail, 2 x motor, 2 x acc. Plus, mass, 4 FU outputs, 2 x speakers), 2 solder pads (other FU outputs).

Z21 multiMAUS

Doehler & Haass SD22 vehicle sound decoder PluX22 2.0A SX1 SX2 DCC MM DC AC. Version with 8-pin interface connector.For optional operation with a conventional DC controller, digital systems according to SelecTRIX 1 and 2 or according to the NMRA standard (DCC)Switching between analogue and digital operation takes place automaticallyIn digital operation, the last programmed one is used system used (it is not switched automatically!)SelecTRIX 1 31 speed steps, 100 addressesSelecTRIX 2 127 speed st

Permanent magnet such as 220450, for Anker 200680, D = 18.0mm, for engine plate 204900 (small disc collector motor). For the conversion of old Märklin® all-electric motors you need a permanent magnet. It replaces the previous field winding and helps your old locomotives in conjunction with a LokSound or LokPilot decoder to a driving behavior that you would never have expected the locomotives! In total, there are four different magnets, which is needed exactly depends on the anchor type. The numb

Permanent magnet such as 220560, for armature 217450, D = 24.5mm, for motor plates 216730, 211990, 228500 (large disc collector motor). For the conversion of old Märklin® all-electric motors you need a permanent magnet. It replaces the previous field winding and helps your old locomotives in conjunction with a LokSound or LokPilot decoder to a driving behavior that you would never have expected the locomotives! In total, there are four different magnets, which is needed exactly depends on the an

SwitchPilot 3 servo decoders are optimized for stationary use on your system and can control up to eight RC servo drives. In order to simplify the rather cumbersome configuration of solenoid decoders, the SwitchPilot 3 Servo has an innovative operating concept consisting of a 4-line, illuminated OLED display and three input buttons.Operating modesThe SwitchPilot 3 Servo is multi-protocol capable and can be used with central units based on the Märklin® Motorola® system (e.g. 6021, Central Station

Basic device MX10 + Fahrer MX33FU + USB stick + CAN cable + 8pola1m + power supply NG300 + operating instructions (MX10, MX33)

Basic device MX10EC + Fahrer MX33FU + USB stick + CAN cable + 8pola1m + power supply NG300 + operating instructions (MX10, MX33)

22-pin SMD pin header (as it is mounted on Plux Decoders as a plug)

Function Decoder, 20 x 11 x 3.5 mm, 1.0 A, 8 function outputs, with 16-pin PLUX16 interface NEM658.

Decoder MX636VD with 21MTC interface NEM660, 26 x 15 x 3.5 mm, 1.8 A, 6 function outputs, energy storage connection also for 16 V ELKOS and gold caps, semi-synchronous rectifier for higher motor current and total load capacity (up to 1.8 A ), with additional adjustable low voltage.General properties of ZIMO Decoders: DCC addresses 1 ... 10239, composite addresses 1 ... 9999 (SB 2017, Veren: 127), mm addresses 1 ... 80, functions F0 ... F12 ( .. F20 for sound), 14, 28 or 128 (external) driving st

MN300R digital decoder 1.0A 8-pin interface NEM652 on wires. Variant of the MN300, 8-pin interface NEM652 on wires, 3 free wires.Technologically, Zimo non-sound decoders correspond to the MS sound decoders. The identical microcontrollers and largely the same components for the power electronics (motor output stages, etc.) are installed in both product classes, and of course the software is also (further) developed jointly to a large extent. These similarities cause, among other things, the same

MN170N digital decoder 0.7A 6-pin interface NEM651 on decoder no wires. 6 FA 6-pin interface NEM651 on decoder, no wires.Technologically, Zimo non-sound decoders correspond to the MS sound decoders. The identical microcontrollers and largely the same components for the power electronics (motor output stages, etc.) are installed in both product classes, and of course the software is also (further) developed jointly to a large extent. These similarities cause, among other things, the same driving

Rundautspeaker 28mm x 6mm, with intermediate resonant body 8 ohm / 1 W.

Round speaker 28 mm, preferably to use in locomas provided for the installation of such a loudspeaker, so integrate the resonance body in the locomotive housing, 8 ohm / 1 W.

Miniature Rectangle Speaker with integrated resonance body, 11 x 15 x 7 mm, 8 ohm / 1 W.

Adapter board for connecting PluX22 decoders to special 21MTC boards that require 5 V levels at the logic level outputs.Only required for special 21MTC locomotive boards - e.g., Sudexpress Eurodual, Stadler BR 159, LS Models BR 120, or LS Models BR 184 (reissues from 2023) - to use a PluX22 decoder (only MX633P22, MX635P22, MN330P22, MS450P22 - NOT MX645P22)New Revision C from July 2023: RevC suitable for Sudexpress Eurodual, Stadler BR 159, LS Models BR 120, and LS Models BR 184.16.8 mm x 19.5

GER: SD 2000 für Magnetartikel

110 VA, 220-240 Volt Switched Mode Power Pack, DE/EU

Switching power supply (Japan) for connecting or supplying the Central Station 60216, 60226 and 60214/60215 and the Booster 60175 and 60174. 100 to 240 V/50 Hz input / 19 or 22 V/100 W DC output switchable. Connection: 4-pin mini DIN high-current plug. The cable cross-section from the Central Station to the track must be at least 0.5 mm²! Recommended exclusively for track 1.

Switch-mode power supply unit (Australia) for connecting or supplying the Central Station 60216, 60226 and 60214/60215 and the Booster 60175 and 60174. 100 to 240 V/50 Hz input / 19 or 22 V/100 W DC output switchable. Connection: 4-pin mini DIN high-current plug. The cable cross-section from the Central Station to the track must be at least 0.5 mm²! Recommended exclusively for track 1.

UK switched-mode power supply unit for connecting or supplying the Central Station 60216, 60226 and 60214/60215 and the Booster 60175 and 60174. 100 to 240 V/50 Hz input / 19 or 22 V/100 W DC output switchable. Connection: 4-pin mini DIN high-current plug. The cable cross-section from the Central Station to the track must be at least 0.5 mm²! Recommended exclusively for track 1.

Power supply 320W (30V; 10.7A) Meanwell HLG-320H-30A; 23x9x4,5cm; 1.8kg;

Locomotive board for the Zimo-MS950 decoder.8- and 9-pin socket strips34 solder pads, arranged on three sides, for locomotive wiring4 three-pin pin strips for direct connection of servos (servo 1 and -2 are always available, servo 3 and -4 when the SUSI pins are switched to servo operation.Dimensions: 61 x 24.5 x 20 mm (height with MS950 decoder)Delivery without MS950.