Central Station 3 plus

ELKOS for Decoders of Category 2 (with direct energy storage connection), 25 V variant (ie MX Decoder with 21MTX interface). Usually several elkos are connected in parallel: at least 3 recommended, at MX Decoders a maximum of 10 - for the permissible total capacity of 6800 ?F, in MS Decoders unlimited number).Contents: 50 x ELKO 680 ?F / 25 V, 10 x 20 mm (change to ELKOS with higher energy density for availability possible).

Digital for beginners, Part 3 - German

Stationary setup module Stein in full equipment, ie: 8 connections for track sections (up to 8 A, HLU, occupation message, etc.), 8 connections for switching drives (double coils, motors) or 16 individual outputs, 16 inputs (div. Sensors, light barriers , Contact tracks, ...), 1 I²C bus, 2 speaker outputs, 2 slots for expansion boards. Included: approx. 2m 20pol ribbon cable incl. 2x 20pol Crimp plug, 4pol plug, 4x 3pol plug Kl., 3pol connector Gr., 2pol plug, instructions.

Basic device MX10 + Fahrer MX33FU + USB stick + CAN cable + 8pola1m + power supply NG600 + operating instructions (MX10, MX33)

8-pin connector board NEM652 for converting to a R-type

Decoder MX635VP with 22-pin PLUX22 interface NEM658, 26 x 15 x 3.5 mm, 1.8 A, 10 function outputs, connection for energy storage 16V (arbitrary capacity, also gold cap), semi-synchronous rectifier for higher motor current and total load capacity (until 1.8a), low voltage source for function outputs (1.5V).General properties of ZIMO Decoders: DCC addresses 1 ... 10239, composite addresses 1 ... 9999 (SB 2017, Veren: 127), mm addresses 1 ... 80, functions F0 ... F12 ( .. F20 for sound), 14, 28 or

22-pin (2 x 11) female strip in raster 1.27 mm, as a mating plug for Decoder with 22-pin or 16-pin PLUX pin strip to pluggle the Decoder in locomas without interface and thus simply make interchangeable. Suitable e.g. For Decoder, which are intended for locomotives with built-in Plux plugs.

Sound Decoder with NEM 658 22-pin PLUX22 interface, 30 x 15 x 4 mm, audio 3 W (4 ohms), 13 Connection wires (2 x rail, 2 x motor, acc. Plus, mass, Elko Plus, 4 FU outputs , 2 x speakers), 6 solder pads (other FU outputs), direct connection energy storage 15 V (unlimited capacity) on Plux pin strip.

The IR scanner is a locally deployed sensor unit for capturing vehicle-related information at defined points along the route. While driving, it records relevant vehicle data in real time and makes this information immediately available to the traffic infrastructure. This enables situation-dependent control of lanes, access points, and special zones – precise, automated, and efficient. Continuous data acquisition allows for the targeted differentiation of traffic flows.For example, short vehicles

The InductiveCharger enables wireless recharging of vehicles as well as inductive communication with the vehicle. It is comparable to the IR Traffic smart Art. 8405, but without its infrared reading function. Vehicles stop on the module and position themselves automatically over the charging coil, whereby charging currents are automatically adjusted.These modules are particularly suitable for locations with longer stopping times such as traffic lights, railway crossings or petrol stations. Sever

The module allows a variety of commands to be transmitted to the CarMotion vehicles via infrared signal. From simply flashing to braking and stopping CarMotion vehicles, e.g. B. in front of traffic lights. The two infrared transmitting diodes can be placed inconspicuously next to the road, but also lying in a small section in the road or in the shoulder. Like the vehicles, the module can be conveniently configured in the CarManager. All macros that are stored in the vehicles can be called up by

4-pin connection cables between Decoder and SUSI module (also for Mxulfa)

1 x StayAlive controller STACO3A (10x7.3x2mm) for decoders without or with limited provisions for direct energy storage connection. 2 miniature gold caps (solder bridge) can be connected via the two free wires via STACO3A. Suitable for N & TT frame models only.Scope of delivery: 1x STACO3A and 2x mini gold caps, 0.3F/2.7V, 4x12mm.

Zimo USB stick, as well as the delivery of the MXulf, as a substitute stick

Double-turn Decoder, 19 x 11 x 3.5 mm, 0.8 A (tip 2.5 A), for 2 double coils, motor or EPL drives, 4 inputs for position feedback or foreclosure, 8 connection wires.The accessory Decoders of the MX820 family are switched to switching and feedback from soft, light and shape signals, magnetic decouplers, etc. Used. The small size allows installation into the track bedding of or in drive housing, for example from LGB turns. All drive types for soft and shape signals are supported by double coils, m

Function Decoder, 20 x 11 x 3.5 mm, 1.0 A, 8 function outputs, with 8-pin interface NEM652 on wires.

GER: LED-Beleuchtungsbausatz Innenbeleuchtung für WRm 61

The Zimo Digital Centers: No big boxes, but state-of-the-art technology:At first glance, the very small dimensions (depending on the type 18 and 15 cm wide, 3 cm high) fall on, as well as the absence of heat sink and fans. Thanks to state-of-the-art Leistungslelektronik - five high-frequency switching regulators for rail outputs and auxiliary voltages - the device running despite 20 A (MX10EC: 12 A) on the rail and 5 A on the bus not hotbut the ZIMO system takes the same consideration for applic

DCC operation, Motorola® operation, M4 operation (mfx® compatible), Selectrix® operation, DC analog operation, AC analog operation, DCC programming, 6021 programming, Mobile / Central Station®, M4 programming and automatic logon, RailCom® with RailComPlus®, ABC-, Selectrix®, Märklin®, HLU brake lines, ABC shuttle train, connection possibility for PowerPack, 32 functions switchable (depending on the control panel), updatable with ESU-LokProgrammer. LokSound 5 Soundengine: 10 channels. 16 bit HiFi

Decoder ELNA Next18.

Decoder Next18 according to NEM662.

Decoder Next18 nach NEM662

Cable set with 8-pin socket to NEM 652, DCC cable colors, 300mm length. If the locomotive to be converted does not have a digital interface, but you do not want to cut off the interface connector of the decoder, our cable sets 51950 or 51951 will help you: First install a suitable cable harness and then simply plug in the decoder. How to digitize the pros!